Видео

Hi, do you know if a zeta lowering kit can be used in these style forks? Looking to lower a 01 yz125.

What ive found is that on my zx7 forks i can tap the lower bushing in first, then slide the inner tube and washer, seal, snap ring, and dust cover. I compress the fork completely and can get the top bushing in by pressing it down with a small screwdriver. No makshift tools and no expensive slide hammers. Just a mallet and screwdriver.

Is it okay to use permatex as gasket between the cases?

Definately a case of you get what you pay for. As stated if it's a bike you use and rely on all the time stick with OEM.

I JUST BOUGHT A KX250 2003 ITS GOT ROCKET RON FRONT SUSPENSION AND I NEED TO DO THE REAR SHOCK ,,RESEAL OR REPLACEMENT SHOCK?? IM NOT A RACER,AND MEDIUM JU😅MPS AND WOODS RIDING,, THANKS

great

I wish my state had a 7% sales tax rate!

Guessing you have to split the case to replace the crank shaft seal? 🤦‍♂️

Excellent, thanks!

My first bike was a 2004 Honda crf450r.it was awesome.traded it straight up for a 87 Honda xr600r.bought a 2000 cr250r now so I have both.ive only owned these three bikes.everyone says I'm nuts for learning how to ride on a 450.love my xr600r.

Try soaking in vineger/water overnight first. Will save u a ton of sandpaper

On 7:22 in this video you have two screws there to hold that bearing, but in the Kawasaki manual there´s only one. Also i had only one screw to hold it when I tear my engine. Should i put it with two screws now when assemble engine back together?

Thank you! Rebuilding a Honda Magna love from Vegas ❤️‍🩹

It kinda worked for me but the tape started sliding up on the layers. Had to redo it a few times and then I just taped end of a flathead and hammered it around until the groove was visible. Hopefully I didn't damage it too much.

Can you provide link for the kit?

I never raced one but when i raced my 97 cr250 i rode a 99 kx250. My impression was cushy, less vibration, felt taller, good pull, not as much overrev. It was easier to ride faster for longer than my bike.

Does the same results apply to 125?

I like to lightly grease most gaskets just prior to install, come off way cleaner next time you take apart. As always great stuff dude!!

Great infos. Good job and i have a question. I got a sandblast machine. You think its good for clean up if i protect the pivot point to clean up.

kx no reliability ive had 2 cr is more reliable but sometimes tits a crap shoot rm is same as cr but worse yz now there u go great all.around champ

Great to know!! Thank you

Just finished my 00 kx250 build thanks to you. Your wisdom is greatly appreciated

Love it, I'll be rebuilding my kx250 in winter, very nice tool video.

Calm down everyone. Bike has been ridden. Check out the Whiskey Throttle media video and Greg test road it before he shipped it because he’s a very wise man.

I'm curious. I have seen you rebuild bikes. Around how much will I spend to do a full rebuild on my 2005 kx250

Man it sounds so good! You built some truly amazing machines.

An excellent informative video. Thankfully I have all the nominated tools you have recommended. You can't have too many specialised tools. Keep up the good work

I’m getting ready to tackle this monster. This video should be the perfect partner

What a stupid comment!

my bike came with a bump on the seat(used) how is the install with a bump seat?

Hi am Charles fro Ghana, my turbo charger is not working i need help please

😢

“Everyone in this room is now dumber for having listened to it.”

I got Vp 108 octane from the pump for 14$ a gallon I had to drive 50 mile round trip but it was nice rural backroads w 65° weather w the top down in my Honda S2000 was a fun ride and good deal I think 😊

You have a Beautiful Sickness Greg,I been watching the Build of this Bike…Good Job🤘🏁🔥

2020 s1000rrr fork oil capacity?

Z-50 1984

I work on bikes professionally and I’ve gotten away with cheaper methods but this is brilliant!

I’m so happy I have my 06 rm 250!

Looks like you opened up a can of worms towards the end there 😅

Great video I have a 2006 RM 250 also and I love it

good video man, but for stubborn kick starters use a small bearing or steering wheel puller and wd 40. 5 minutes and viola

Hey I got the same one no joke

great video 👍

Amazing video, and custom tool is priceless advice, thank you!!! Saved me so many headaches

Thank you!!!

Saludos desde Ecuador Estoy restaurando una modelo 98 kx

Thank you!!!

Good tips 👍 thanks

Those sockets are awesome!